Pioneer GM-D9701 Mono Block 2400W Class D amplifier with bass remote Reviews

4.5 Rating 12 Reviews

Visit Product Page

Phone:

0330 320 5050

Email:

sales@caraudiocentre.co.uk

Location:

29 Bridlesmith Gate,
Nottingham
Nottinghamshire
NG1 2GR

Visit Product Page

Patrick Dickson

Verified Reviewer

“Plenty of punch for its size a great product”

Helpful Report

Posted 4 months ago

“Great little amp, running very well with plenty of good bass. I did have the inphase one which is recommended first, which spent most of the time of ownership in the shop getting repaired opted for this as a replacement, much happier now”

Helpful Report

Posted 2 years ago

“I'm currently running this amp to power a Pioneer TS-D12D2 12" Dual 2 Ohm Voice Coil Subwoofer. I must say that I am quite happy. I've currently got the sub wired up as a 4ohm load. I set the gain using my oscilloscope with a 50hz signal. I have also tried wiring the sub as a 1ohm load, and although it was obviously able to get it a litre louder (limited by a 600w rms sub) I found the sound wasn't as clean as in a 4ohm configuration. I also borrowed my friend's sub (same as mine) and wired the 2 subs up as a 2ohm load. Although my van was certainly shaking, this amp is a was a little under powered for both subs. The amp with a 2ohm load can only produce 800w rms which is 400w under the 2 subs total of 1200w rms, I think this is where people my have been feeling a little let down. I have had no over heating issues in any of the wiring configurations and have had the amp running full volume for a full 30 minutes. The amp is also mounted upside-down to the roof of my van. From my experience with this amp, I would say make sure to match it up with a correct rms sub (and this will depend on the wiring configuration/load). I would probably say, keep things within 100w of the rms, e.g. 4ohm 400-600w rms sub. 20hm load 700-900w rms sub or 2 subs to that total. 1ohm load 1100-1300w sub or 2 subs to that total. I will eventually be using this amp to power 3 x 350w rms 4ohm single voice coils shallow subs wired in parallel for a 1.33ohm load. If I have any issues I will update the review. My crosser is set as follows. Sub up to 80hz 12db slope Mids 90 to 2.5khz 6db slope Twitter 4khz 12db slope I hope someone finds the above info useful.”

Helpful Report

Posted 3 years ago

“Returned after 7 days. Because the low end was crap. I though it was a faulty amp so I got a replacement. Replacement sounds just as crap. Returning for a refund. Will buy the IPA2001D on payday”

Helpful Report

Posted 3 years ago

“The inphase amp deal with kenwood sub, would the amp run in bridge mode? Or is a better 1 ch amp on offer. Looking to buy online but need good deal. Already run 0 guage from battery and power gain switch and quality rca leads.”

Helpful Report

Posted 4 years ago

“I have this running 2 x Vide black air 122 and it really struggles, thelow end it bottoms out and I dont think the power it quotes is correct. Not reconemdnend”

Helpful Report

Posted 4 years ago

“This little gem was recommended to me by ilford branch for my twin alpine setup. Cannot believe the price of it for that sort of power. Glad i visited your ilford branch, cause another shop suggested different make amplifier for double the price. you have a great team at your ilford branch.”

Helpful Report

Posted 5 years ago

“RECIVED THE AMPLIFIER . HAPPY BECAUSE ITS 100% ORIGINAL PRODUCT. 0RDER NO CA.........”

Helpful Report

Posted 5 years ago