Login
Start Free Trial Are you a business?? Click Here

Red Dot Sight Mount for Smith and Wesson (S&W) M&P (fits Trijicon RMR / SRO, Holosun 407c / 507c) Reviews

4.7 Rating 26 Reviews
Read EGW Guns Reviews

Mounting Hardware is Included This is a press fit mount. Utilization of a sight pusher tool may be required.
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH. This mount will fit:
Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact Smith & Wesson M&P 2.0 Compact Smith & Wesson SD9VE Smith & Wesson SD40VE Smith & Wesson M&P Shield
This mount does not fit:
Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P Shield EZ 9mm Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
The hole for the set screw on this mount is drilled off-center intentionally. This is to allow the set screw to be tightened against the bottom of the dovetail cut in the slide. This creates an upward force on the dovetail of the mount. If the hole were cut in the center of the dovetail, the set screw would fall through the hole cut in the center of the slide which would render the set screw useless.Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering. Our return policy does allow for returns of unused and undamaged parts. These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Please note: Trijicon recommends the use of a sealing plate to prevent water from entering their red dots. Material: 7075 AluminumCoating: Matte Black HardcoatOverall Length: 1.780Overall Width: 1.1"Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set ScrewRed Dot Fitment: Trijicon RMR / SRO, Holosun HE407C / HE507C / HS407C / HS507C, Swampfox Kingslayer / Liberty / Justice Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.Installation Instructions- Remove the rear sight*- Install the EGW Sight Mount in the dovetail- Tighten set screw (if applicable)- Place the red dot sight on the EGW Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)- Apply blue Loctite to the provided mounting screws- Torque mounting screws to 15in/lbs*Rear sight pusher tool highly recommended*
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH. Modification of your firearm may nullify the manufacturer's warranty.This product should be installed and checked by a qualified gunsmith.No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Visit Product Page

Location:

52 BELMONT AVE,
QUAKERTOWN
Pennsylvania
18951

Used this mount for a Holosun 407c. Fits perfect. Installation would be much easier with a site alignment tool/vise, but you can do it the old-fashioned way with a hammer and a punch. Be careful with the spring hidden under the rear sight. Especially when reinstalling the optic mount.
Helpful Report
Posted 2 years ago
Awesome American-made company! As a gunsmith and veteran, I am going to use this company exclusively from now on!
Helpful Report
Posted 2 years ago
The mount plate required minimal filing on the dove tail and fit the sight perfectly. I would recommend this mount plate.
Helpful Report
Posted 2 years ago
Nice snug fit. Very secure. Very sturdy. Impressed and will buy again.
Helpful Report
Posted 2 years ago
It came but with no instructions. So I figured it out and it fit onto my Smith and Wesson M&P 40 very tight fit.
Helpful Report
Posted 2 years ago
As described in your product details, the fit could be snug due to S&W manufacturing tolerances. I ended up taking a little bit of material off the bottom of the dovetail before I was able to get the mount properly placed using a sight pusher. I did install the set screw but it is probably not needed. Been to the range a couple of times and everything is zeroed in. Very happy! Really, the completed installation looks like it came directly from the factory.
Helpful Report
Posted 3 years ago
I picked the wrong part number on your page but in the notes I noted what gun I have and what optic I have and apparently no one read the notes and caught it so I called and spoke to Zack and very nice and helpful so I sent it back and now waiting on the new one yes probably my fault but shouldn’t someone of caught it in the notes, no harm no foul you should have the wrong one soon and I will wait for the right one. Thanks and have a blessed day.
Helpful Report
Posted 3 years ago
Very tight fit in the sight dovetail. Had to do a slight amount of filing to be able to drive the mount in place. Set screw is installed but the fit is such that screw is probably not required. My RMR and seal plate went on the mount like they were made for each other. A satisfied customer.
Helpful Report
Posted 3 years ago